I have long since given away my test machine that was running Deli Linux on it, but a friend at the local Linux User Group has installed it on an old Sony laptop, and is chronicling the process at http://www.distasis.com/cpp/dlin.htm. More importantly, she wants to actually use the distro, so there is a lot on the page about what works, changes that will get things working (such as sound, and recognizing USB drives), as well as details about which programs are available and work, and how to get other programs to compile.
Archive for the ‘DeLi Linux’ Category
I wrote about this six months ago (here). I took out the modem on the old machine I had installed Deli on, and put in an Ethernet card. Since a new version of Deli had come out I decided to try it out again from scratch.
The install went pretty much the same as the last time, but this time I tried to configure the local network during the delisetup part (after installation). The delisetup command (at the command prompt after logging in) goes to a text-based setup. (Note: if you try to go straight to a gui interface (by typing startx) without doing the setup, it gives a group of white terminals on an icewm interface; but closing the terminals closes the gui interface). The setup categories are:
- Setup LILO – the Linux Loader
- Setup PPP – Needs data from your Internet Service Provider
- Setup local Network
- Printer Setup
- Setup Tiny X Server
- Setup Window Manager
- Install additional software packages
- Set up your Mail system (with masqmail)
- Select servicesto run at boot
I went through the Setup for local Network. The first screen says you can always go back and make changes by typing netconfig (it says that, but it lies: typing netconfig gets an error message that there is no such command). Then it wants a hostname and domain name. There are instructions with screenshots at the wiki on the Deli site. After the hostname and domain name, you choose between using a static IP, DHCP, or loopback. I tried both static IP and DHCP, but somehow ultimately ended up with loopback. Choosing DHCP will take you through a probe for an Ethernet card. The message I got was “A networking card using com20020.o module has been detected.” Great, but it wouldn’t connect to the network.
I tried “ifconfig” instead of “netconfig” and it showed, despite the Network configuration done in delisetup:
Link encap:Local Loopback
inet addr:127.0.0.1 Mask: 255.0.0.0
UP LOOPBACK RUNNING MTU 16436 Metric:1
After looking at a bunch of config files, going through delisetup several times, and editing the /etc/rc.d/net file, I checked the ethernet card and put it in another slot. But the browser is still giving the error: “dns can’t find slashdot.org.” I think it’s stuck in loopback purgatory, and I don’t have the right incantations to get it out.
On the other hand, it is still a nice, fast distro, even on this old dinosaur, and not that difficult to install, as long as you’re not trying to connect to the Internet.
Awright! Got it up and running ! (The DeLi homepage is here)
The install was pretty straightforward, text based. There is a nice installation instruction page on the DeLi wiki. It pretty much recognized everything (at least as far as I can see right now). At the bottom of the Instruction page, it says,
- After the packages are installed remove the CD-ROM (the disk, not the drive itself) and press
CRTL+ALT+DELto boot into your new DeLi Linux system
- Log in as root with the password you chose before. Now you can run
delisetupto configure your system.
Uh huh, delisetup. Well, that’s where xconfig resides, which is what you need to get a graphical user interface. So I took a deep breath, and tried to gingerly step into the xconfig section of delisetup. It actually wasn’t that bad, even though I had very little information about the monitor and video card (other than the fact that it is not a separate card, and the system is circa 1997). I went back and forth a couple times, trying to make sure I got it right, held my breath again and finished the setup. It took me back to the command prompt.
I stared at it for awhile trying to remember the command to start Xwindows. Checked my cheatsheet card, looked for my pocket Linux book (which, now that I recall, my son borrowed, so it’s probably buried under a pile of God knows what), gave up and decided to go back to book reviews. As I was scanning the Mandrakelinux Discovery 10.1 book I was working on, I happened to spot an entry about entering a command if the graphical version was not displaying: “startx.” Good grief. How could I not remember that? Bingo, we’ve got graphics now!
I poked around a bit, but couldn’t find a utility to set up users, so I’m in there as “root” (normally not a good thing) until I change the settings via the command line interface.
Bottom line: Hey, it works on a 1997 Compaq with 32MB of memory: I don’t think I was really testing its limits! During the install process it asked about using the free space on the disk (which has Windows98 on it, and had over 1GB of free space). On reboot, it actually booted into Win98 because I wasn’t there to choose Linux from the bootloader at startup. Overall,
- Ease of install = medium
- Knowledge required = some knowledge, or a Linux reference, will be really helpful
- Features = limited, but acceptable (this is for low memory machines, after all!)